Allen-Bradley Rockwell Automation 1734-AENT Manual do Utilizador Página 170
- Página / 221
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Rockwell Automation Publication 1734-UM001E-EN-P - July 2013
178 Mounting Dimensions
POINT I/O Module with a
1734-PDN Module
See the figure for mounting dimensions for POINT I/O module with a
1734-PDN DeviceNet Communication Interface module.
L = 1.0 + [# of I/O x 0.47] + [# of FPD x 1.0] in.
Allow a 25.4 (1.0)
air gap all around
133.4
(5.25)
mm (in)
L = 25.4 + [# of I/O x 12.0] + [# of FPD x 25.4] mm
1734-FPD (HxWxL)
76.2 (3.0) x 25.4 (1.0) x 133.4 (5.25)
1734-PDN (HxWxL)
76.2 (3.0 ) x 25.4 (1.0) x 133.4 (5.25)
1734-TB or 1734-TBS (HxWxL)
76.2 (3.0) x 12.0 (0.47) x 133.4 (5.25)
Secure DIN rail to mounting surface approximately every 200 mm (7.8 in.).
- POINTBlock I/O Modules 1
- Important User Information 2
- Summary of Changes 3
- Purpose of This Manual 5
- Who Should Use This 5
- Additional Resources 6
- Table of Contents 9
- Chapter 3 11
- Chapter 4 12
- POINT I/O Module Data 12
- Chapter 5 13
- Chapter 6 13
- Troubleshoot with the 13
- Indicators 13
- Appendix A 14
- Default Data Maps 14
- Appendix B 14
- Mounting Dimensions 14
- xxiii 15
- About the Modules 17
- Input Modules 18
- Output Modules 18
- Analog Modules 19
- Specialty Modules 21
- Power Supplies, Wiring 21
- Base Assemblies, and 21
- Miscellaneous Modules 21
- 6 About the Modules 22
- Install POINT I/O Modules 23
- Explosion Hazard 24
- Install the Mounting Base 25
- Assembly 25
- Install an I/O Module 27
- Install the Removable 28
- Terminal Block 28
- Remove a Mounting Base 29
- Wiring Digital Modules 30
- 24V dc Return 32
- DeviceNet 32
- 1734-IB4D Modules 34
- C = Common 38
- V = Supply 38
- Wiring Diagram 42
- PDN OW2OW2 44
- AC Power Bus 44
- 01 01 0101 01010101 45
- 01 01 0101 01 50
- 01 01 01 50
- Wiring Analog Modules 58
- 00 2 4 6 59
- 11 3 5 7 59
- Wiring Power Distribution 62
- NC = No Connection 63
- CHAS GND = Chassis Ground 63
- C = Common V = Supply 63
- 12/24V DC Wiring Diagram 67
- IMPORTANT 68
- 120/240V AC Wiring Diagram 69
- 0101 01 01 0101 01 01 70
- 0101 0101 70
- Sink Input Wiring Diagram 72
- Wiring POINTBlock 75
- Sink Input Wiring 76
- Diagram 76
- RTB 0 RTB 1 RTB 2 RTB 3 RTB 4 76
- Output Wiring Diagram 77
- DeviceNet Connector Wiring 78
- Diagram 82
- Input Wiring Diagram 83
- Digital AC Input Modules 95
- Digital Output Modules 96
- Digital AC Output Modules 98
- Relay Output Modules 99
- Analog Input Modules 100
- Communicate with Your Module 101
- Channel Status 102
- Latch Alarms 103
- Notch Filter 104
- Alarm Disable 104
- Calibration Status 104
- Digital Filter 104
- Update Rate 104
- Range Status 105
- Analog Output Modules 106
- Operational Modes 108
- Scaling 108
- Low and High Clamps 110
- Channel Indicators 111
- Message Size: 2 bytes 115
- Calibrate Your Analog Modules 117
- Tools Required to Calibrate 118
- Your Analog Modules 118
- Calibrate the Analog 119
- Current Input Module 119
- This is the group 120
- Leave on single 121
- 01 01 01 01 123
- Group pull-down 124
- Groups pull-down 132
- Click Calibration 132
- (-10.1234 in the example) 134
- About This Chapter 137
- Troubleshoot Digital 139
- Modules 139
- 1734-OB2E 1734-OB4E 140
- 1734-OB8E 140
- 1734-OB2 1734-OB4 140
- 1734-OB8 140
- 1734-IV2 1734-IV4 141
- 1734-IV8 141
- 1734-OV2E 1734-OV4E 1734-OV8E 142
- 1734-OX2 Relay Output Module 143
- I/O Status 144
- 1734-OA2 144
- 1734-OA4 144
- 1734-IM2 144
- 1734-IM4 144
- Troubleshoot Analog 145
- Troubleshoot I/O 147
- Communication Modules 147
- 1734-ADN DeviceNet Adapter 148
- 1734-ADNX DeviceNet Adapter 148
- • Firmware fatal error 150
- 1734-APB PROFIBUS Adapter 152
- • No power supplied 153
- 1734-AENT 154
- Digital Module Default 158
- Data Maps 158
- Where: OW = open wire 159
- 1734-IV2 Source Input Module 160
- 1734-IV4 Source Input Module 160
- 1734-IV8 Source Input Module 160
- 1734-IA2 Input Module 161
- 1734-IA4 Input Module 161
- 1734-IM2 Input Module 161
- 1734-IM4 Input Module 161
- 1734-OA2 Output Module 162
- 1734-OA4 Output Module 162
- Message Size: 1 Byte 163
- 1734-OV2E Output Module 164
- 1734-OV4E Output Module 164
- 1734-OV8E Output Module 164
- Analog Module Default 166
- Message Size: 4 bytes 167
- Message Size: 2 Bytes 167
- 176 Default Data Maps 168
- POINT I/O Module with a 170
- 1734-PDN Module 170
- POINTBlock Module 171
- Software 173
- For Module 175
- Connection Type 175
- Configure Analog Modules 183
- Networks 197
- Using RSNetWorx Software 199
- Configure Digital Modules 199
- Configure Input Modules 200
- Configure Output Modules 203
- • Autobaud - Enable/Disable 209
- • Go to Fault Value 215
- Numerics 217
- 226 Index 218
- 228 Index 220
- Rockwell Automation Support 221
- Documentation Feedback 221
Manuais e produtos relacionados com Redes Allen-Bradley Rockwell Automation 1734-AENT
Redes Allen-Bradley 1794-IE8H Especificações
(136 páginas)
(136 páginas)
Redes Allen-Bradley 1738-ADNX Manual do Utilizador
(112 páginas)
(112 páginas)
Redes Allen-Bradley 1734-ADN Manual do Utilizador
(239 páginas)
(239 páginas)
Redes Allen-Bradley PLC-5 Manual do Utilizador
(2 páginas)
(2 páginas)
Redes Allen-Bradley 1784-KT/B Especificações
(67 páginas)
(67 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais